67 lines
2.3 KiB
C
67 lines
2.3 KiB
C
#include "DcMotor.h"
|
|
#include "stm32f1xx_ll_gpio.h"
|
|
#include "stm32f1xx_ll_bus.h"
|
|
#include "stm32f1xx_ll_tim.h"
|
|
|
|
#define ARR_DC_MOTOR 50000
|
|
void DC_MOTOR_Init(void) {
|
|
// use TIM2 since it has pa1 at channel 2 output
|
|
// setup timer 2
|
|
LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_TIM2);
|
|
LL_TIM_InitTypeDef tim_init;
|
|
// todo check switching behavior of the mosfet to determine period of switching
|
|
tim_init.Prescaler = 71;
|
|
tim_init.Autoreload = ARR_DC_MOTOR - 1;
|
|
tim_init.ClockDivision=LL_TIM_CLOCKDIVISION_DIV1;
|
|
tim_init.CounterMode=LL_TIM_COUNTERMODE_UP;
|
|
tim_init.RepetitionCounter=0;
|
|
LL_TIM_Init(TIM2, &tim_init);
|
|
|
|
// setup gpio
|
|
LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_GPIOA);
|
|
LL_GPIO_InitTypeDef servo_gpio_init;
|
|
servo_gpio_init.Pin = LL_GPIO_PIN_1;
|
|
servo_gpio_init.Mode = LL_GPIO_MODE_ALTERNATE;
|
|
servo_gpio_init.Speed = LL_GPIO_SPEED_FREQ_LOW;
|
|
servo_gpio_init.OutputType = LL_GPIO_OUTPUT_PUSHPULL;
|
|
LL_GPIO_Init(GPIOA, &servo_gpio_init);
|
|
|
|
// setup output compare
|
|
LL_TIM_OC_InitTypeDef oc_init;
|
|
oc_init.OCMode = LL_TIM_OCMODE_PWM1;
|
|
oc_init.OCState = LL_TIM_OCSTATE_ENABLE;
|
|
oc_init.OCNState = LL_TIM_OCSTATE_ENABLE;
|
|
oc_init.CompareValue = 0; // off at start
|
|
oc_init.OCPolarity = LL_TIM_OCPOLARITY_HIGH;
|
|
oc_init.OCNPolarity = LL_TIM_OCPOLARITY_LOW;
|
|
oc_init.OCIdleState = LL_TIM_OCIDLESTATE_LOW;
|
|
oc_init.OCNIdleState = LL_TIM_OCIDLESTATE_HIGH;
|
|
LL_TIM_OC_Init(TIM2, LL_TIM_CHANNEL_CH2, &oc_init);
|
|
LL_TIM_EnableCounter(TIM2);
|
|
|
|
// init gpio for direction (sense) pin
|
|
LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_GPIOA);
|
|
|
|
|
|
LL_GPIO_InitTypeDef pa2_init_conf;
|
|
pa2_init_conf.Mode = LL_GPIO_MODE_OUTPUT;
|
|
pa2_init_conf.OutputType = LL_GPIO_OUTPUT_PUSHPULL;
|
|
pa2_init_conf.Speed = LL_GPIO_SPEED_FREQ_LOW;
|
|
pa2_init_conf.Pin = LL_GPIO_PIN_2;
|
|
LL_GPIO_Init(GPIOA, &pa2_init_conf);
|
|
|
|
}
|
|
|
|
void DC_MOTOR_SetSpeed(int speed){
|
|
if(speed <= 100 && speed >= 0){
|
|
LL_GPIO_SetOutputPin(GPIOA,LL_GPIO_PIN_2);
|
|
int converted_speed = speed * (ARR_DC_MOTOR / 100);
|
|
TIM2->CCR2 = converted_speed;
|
|
} else if (speed >= -100 && speed <= 0) {
|
|
LL_GPIO_ResetOutputPin(GPIOA,LL_GPIO_PIN_2); // TODO maybe switch around set and reset, depending on direction of turning
|
|
int converted_speed = (-1) * speed * (ARR_DC_MOTOR / 100);
|
|
TIM2->CCR2 = converted_speed;
|
|
} else {
|
|
TIM2->CCR2 = 0;
|
|
}
|
|
}
|